|
Log in to the control panel of video encoder 192.168.1.1681. Reset There is a ''RESET'' hole on the front end of video encoder, which is used for conducting initialization reset to the encoder. After turning on the power of the device, insert a pin into the hole, then press the reset button and hold it down for about 8 seconds until you see all three indicator light(VIDEO, LAN, POWER) go out. All parameters will be initialized. • The default IP address is 192.168.1.168. The default login ID and password are ''admin''. • You can try to reset the device if you encounter any problems while using the device. 2 Log in to the Control Panel This is how to log in to the control panel. If you are using windows, please refer to chapter 2.1; if you are using MAC, please refer to chapter 2.2. 2.1 Windows Operating System Step 1. Connect the video encoder to the router via an Ethernet cable Step 2. Connect the PC(or laptop) to the same router via Ethernet cable or WIFI. Right click on the network icon to open <Network and Sharing Center> Step 3. Click ''Ethernet'' or ''WIFI'' If you connect the PC(or laptop) to the router via WIFI, ''WIFI'' is displayed in here. Step 4. Click ''Details'' You can check the IP address and default gateway of the PC(or laptop) in <Network Connection Status>. For example, the IP address of my PC(or laptop) is 192.168.0.111, and the gateway of of my PC(laptop) is 192.168.0.1. Remember the IP address and the gateway of your PC(laptop), it will be used in step 10. Step 5. Click ''Properties'' Step 6. Double click ''Internet Protocol Version 4(TCP /IPv4)'' Step 7. Select ''Use the following IP address'' Step 8. Change the IP address and default gateway of computer, and then click ''OK'' You can set the IP address to 192.168.1.30 and the default gateway to 192.168.1.1. In order for the IP settings to take effect, please remember to click ''OK'' in the window of <Local Area Connection Properties>. Step 9. Log in to the control panel of video encoder 192.168.1.168 The default ID and password are ''admin''. If you cannot log in to the control panel, please reset the device. (Refer to chapter 1) Usually, the language of the control panel is English. If Chinese is displayed, you can change the language in the upper right corner of control panel. Please select ''英文''. Now the video encoder can be used in local area network(LAN). In order to use it in a wide area network(WAN), we need to change the IP address of video encoder.
Step 10. Change the IP address and gateway of video encoder In step 4, you already know the IP address and default gateway of the computer. For example, the IP address of my computer is 192.168.0.111, and the gateway is 192.168.0.1. Therefore, I can change the IP address of the video encoder to 192.168.0.168 (in order to avoid IP conflicts, please don't make the IP address of video encoder the same as the IP address of your PC), and change the default gateway to 192.168.0.1. Since each computer has a different IP address, I can only use my computer IP as an example. Before changing the IP address and gateway of video encoder, please refer to the IP address and gateway of your computer(In Step 4). Step 11. Click ''Reboot'' to restart the video encoder Step 12. Select ''Obtain an IP address automatically'', and then click ''OK'' Please remember the new IP address of the video encoder. In order for the IP settings to take effect, please remember to click ''OK'' in the window of <Local Area Connection Properties>. Step 13. Log in to the new IP address of video encoder 2.2 MAC Operating System Step 1. Connect the video encoder to the router via an Ethernet cable Step 2. Connect the MAC to the same router via WIFI. Open the window of <System Performance> Step 3. Click ''Network'' Step 4. Click ''Advanced'' Step 5. Click ''TCP /IP'' You can check the IP address and default gateway of the MAC here. For example, the IP address of my MAC is 192.168.0.112, and the gateway of my computer is 192.168.0.1. Remember the IP address and default gateway of your MAC, it will be used in step 10. Step 6. Select ''Manually'' in the setting of ''Configure IPV4'' Step 7. Change the IP address of MAC, and click ''OK''. You can set the IP address to 192.168.1.30 and the default gateway to 192.168.1.1. Step 8. Click ''Apply'' in the window of <Network> Step 9. Log in to the control panel of video encoder 192.168.1.168 The default ID and password is ''admin''. If you cannot log in to the control panel, please reset the device. (Refer to chapter 1) Usually, the language of the control panel is English. If Chinese is displayed, you can change the language in the upper right corner of control panel. Please select ''英文''. Now the video encoder can be used in local area network(LAN). In order to use it in a wide area network(WAN), we need to change the IP address of video encoder. Step 10. Change the IP address and gateway of video encoder In step 5, you already know the IP address and default gateway of the MAC. For example, the IP address of my MAC is 192.168.0.112, and the gateway is 192.168.0.1. Therefore, I can change the IP address of the video encoder to 192.168.0.168(in order to avoid IP conflicts, please don’t make the IP address of video encoder the same as the IP address of your MAC), and change the default gateway to 192.168.0.1. Since each MAC has a different IP address, I can only use my MAC IP as an example. Before changing the IP address and gateway of video encoder, please refer to the IP address and gateway of your MAC(In Step 5). If you have any question, please contact us. We will arrange an engineer to help you set up. Step 11. Click ''Reboot'' to restart the video encoder Step 12. Select ''Using DHCP'' in the setting of ''Configure IPV4'', and click ''OK''. Step 13. Click ''Apply'' in the window of <Network> Step 14. Log in to the new IP address of video encoder |